Handy Do It Yourself Pipes Tips For The Homeowner

Taking the time to learn to do plumbing on your own truly shows when you do it. You can take pride in being able to tackle problems as they arise, and you can stop trouble with proper maintenance. That's quite admirable. Even if you already know a thing or two about plumbing, you can always improve on your skill-set. Below are a few tips that will help you out.

Solder with safety in mind. When you solder a copper pipe you want to direct the flame on the copper pipe. The flame of the torch has to be four inches away from the piping. The flame should be targeted directly at the point where the copper piping needs to be disconnected.

Pump your septic tank every five years to keep it working well. Regular maintenance will keep sediment from backing up inside of the tank. Sediment can not only cause the sewage in the tank to back up into your house, but it can cause the tank to fail completely. The cost to have your tank pumped might be a little steep, but it sure beats the alternative of dealing with sewage in your home or on your property.

Make sure everyone that lives in your house knows where to find and use the main water shut off valve in case there is a burst pipe emergency. This is especially important if you live in an area where your pipes may freeze. Take a moment to show your family members where the valve is and how to properly shut it off.

Find a better way to discard of cooking oil instead of pouring it down the drain where it can easily clog your pipes. Keep a coffee can or other metal container handy to pour grease into after cooking. Place the can in the freezer to harden the grease and when it's full, discard it with the trash.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. navigate to this web-site to the replacement pipe and the remaining pipe. Slide Recommended Internet site of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

There are many ways to unclog a drain. You can try plunging it at first. If that doesn't work try using a chemical agent from the store. Before you go and spend money at the store though, if you have baking soda and some vinegar handy, you can mix those together and pour them in the drain and try to plunge that but if all else fails they have stronger remedies at your local hardware store.

You can drastically reduce your utility bills with the installation of shower heads designed for better efficiency. Energy efficient shower heads can save you money on your energy bill and water bill. You can save up to a few hundred dollars a year by simply installing shower heads that are energy efficient.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

If http://fatima9chase.blogminds.com/it-is-necessary-to-know-a-little-bit-about-plumbing-6838827 have a water pressure or fill problem throughout the whole house, do not panic. It could be the simplest of solutions. Sometimes the city flushes their systems, breaking up debris and sending it to homes. This requires cleaning drains effectively and strainers in order to resolve the problem.

One way to avoid a common plumbing problem is to make sure never to flush anything but human waste and toilet paper down a toilet. Other things made of paper like tissues, paper towels, and the like do not dissolve the same way toilet paper does and can get stuck.

To avoid hair from accumulating and clogging pipes. Use simply click the up coming site in every drain where hair is washed. Fine mesh strainers can catch the hair and still allow the shower, tub or sink to drain and are also useful in the kitchen to catch and stop small food debris from going down the drain.

If you are going to update the plumbing in your house, one thing to consider is installing a new tank-less water heater. They are much smaller than traditional tank heaters, which is a space-saver. Tank-less water heaters are available in gas or electric, depending on what your house needs.


Check to make sure that the walls behind the tiles in your bathroom are not soft. Push into the tiles to confirm that the foundation is firm and robust. If the area is delicate and brittle, there is a good chance that water has created damage behind the tiles over time.

Be sure to have a running toilet fixed as soon as you can. Having a running toilet uses more water, which raises your water bill. To fix it yourself, you just have to find out what the problem is and buy the supplies you need. If you can't fix it yourself, call a plumber.

To make sure there is no accident or sudden rush of water when you tackle a plumbing project, make sure you are ready for a cleanup. If you go into the work with a huge stack of towels and blankets ready to absorb water, the prospect of needing to actually do it will keep you alert enough to avoid triggering the accident in the first place.

Always try plunging any clogged toilet or drain before snaking. Snaking can often push problems further down the pipe and make matters worse. A plunger uses nothing but your strength and water pressure to help clear clogs. For more effective plunging, boil some water and pour into the affected drain or toilet to help loosen things up before plunging.

Tank-less water heaters are a great space saving alternative to traditional tank units. They are available in many models, some for indoors and some models are capable for outdoor mounting. Tank-less water heaters are known as great money savers when it comes to your water bill.

To help keep your drains working properly you should pay attention to clogs. Clogs are a common problem at home but with proper maintenance and preventive measures you can avoid a messy situation. Clogs are not only an annoyance, but can also lead to overflows and water damage. So make sure you keep your drains clog-free by implementing easy preventative practices.

Plumbing is actually a serious thing, and when you know what the issues are and how to deal with them, you are that much closer to fixing them. Keep these tips on hand while you tackle your plumbing project. Whether you decide to do-it-yourself or call for professional intervention, they will help you gain a better understanding of the situation. Educating yourself is the key to a successful outcome.

What You Ought To Perform In A Plumbing Situation

Professional plumbing is often a very expensive service, and usually the work that is done is something that any homeowner could solve fairly easily with the proper knowledge and tools. If you'd like to start learning to solve your own plumbing problems, read on to see what you can do.



Do not pour grease or oil down any of your household drains. Put them in containers and place in the fridge until they are solid, then throw them away. If you pour them down the drain, they can solidify in cold pipes. These solid masses will clog your pipes and are very difficult to remove.

If your toilet is slow to flush, add some white vinegar to the overflow tube. White vinegar helps the water from your tank to flow quickly, which will make the toilet flush faster. It is recommended that you use about a quart of the vinegar and let it stay there for at least an hour before flushing.

Have a professional flush your septic tank every five years or so to keep it working well. Having https://timesofindia.indiatimes.com/business/india-business/are-plumbers-carpenters-the-answer-to-indias-unemployment-problem/articleshow/65528837.cms pumped will keep sediments from settling to the bottom of the septic tank and causing the tank to malfunction or backup. In this case, the cost of prevention definitely outweighs having your septic backing up into your house or failing.

Check how well your toilets are flushing. If the handle needs to be played with in order to keep the water from running constantly, or if it needs to be held down several times in order to flush, you may need to switch out some of the parts in your tank. This is not expensive, and it could help reduce your monthly water bill. It could also mean that you avoid the embarrassment of the flushing system breaking when you have visitors!

Avoid using hard cleaners on your toilets, such as drop-in cleaner tabs in the tank. When these tabs are almost completely dissolved, what's left of the tab gets washed into the bowl. This can then end up clogging the toilet's port holes, preventing the toilet from flushing properly. It can take months for this debris to finish dissolving in those holes.

If you have problems with a slow drain, there are easier things you can do other than removing the pipes to clean it. There are certain tools made just for this purpose that you insert into the drain to loosen the clog so it washes away or grab it and remove it completely.

Have your pipes in your plumbing system frozen? You can skip the cost of hiring a plumber by using this method. First, open the faucet so steam produced by the thawing process can escape. Begin thawing close to the faucet, and move down the line as each section thaws out. Use a hair dryer or a heat lamp to warm along the pipe. Even though this method consumes quite a bit of time, it is safer than most other heating methods. Furthermore, it requires no cleanup.

It is not always necessary to call in a plumber when you have a damaged section of pipe in your plumbing. There are repair kits you can buy in your local hardware store which are excellent in repairing leaks. If you have a small leak, you can rub a compound stick over the hole or crack in the pipe to seal it shut. Epoxy paste is also an excellent remedy for a leaking pipes. Make sure you turn off the water and completely dry the pipe before applying the epoxy.

Never hire websites that is not licensed, insured and bonded. If the plumbing company cannot provide you with reference numbers for their credentials, move on quickly. It is a common question and it should be a no-brainer for them to provide them to you. If they have issues with you asking, take that as a big red flag.

Periodically, make sure that the sump pump in your house is working to full capacity. Pour a few gallons of water into the sump pit, and your pump should drain that water out with minimal issues. Checking that your devices are working throughout the year can pay large dividends in the event of a crisis.

Make sure that any exposed pipes in your home are insulated, especially those found in crawl spaces on the outside walls of your home. This will help keep them from freezing and causing you tons of problems. Frozen pipes can often be devastating and leave you with problems that are expensive to fix and no water in the middle of winter.

If water is backing up into multiple fixtures all over the house, it is no longer going to be effective for you to use chemicals or a small hand snake. This is evidence of a blockage in the main line, and you must contact a professional to take care of this problem for you.

Look at your hot water heater and make sure that the temperature is not higher than 120 degrees Fahrenheit. If it is, it could cause you to get burned or it could reduce the unit's energy consumption. If you determine that the temperature is too high, adjust immediately to avoid any of these things from happening.

It is a general rule of thumb that you should replace a water faucet every seven years, even if you do not see anything wrong with it. Some faucet problems are not visible to the naked eye, which is why it is so important for them to replaced every so often.

Have a specific plumber in mind before you have an emergency. Most people don't think about plumbers until they find themselves having a big problem that needs to be fixed right away. Instead, choose a plumber who you are comfortable with and whose experience you trust--way before you actually need his services.

Make sure that you avoid throwing fats down the drain after you clean up your meal. Fats can solidify over time which can cause a drainage problem and corrupt your water flow. Throw out fats and different types of cooking oils in the garbage after you finish with your meal.

You should try using a plumbing snake or plumber to unclog a clog. Liquid cleaners that are meant to unclog the clogs in a drain could ruin the pipes. You should also use strainers to catch hair so that it doesn't go down the drain and get clumped and clog your drain.


While you may not be able to tackle every problem that comes up, you can surely feel more confident about dealing with some of the basic stuff. Take any situation step by step, and you will find that it's not as difficult as you may have thought.

Solid Plumbing Guidance For The Do-It-Yourself Property Owner

When https://goo.gl/RCrH2r are working on your plumbing, there is a lot that can go wrong. A few things can be easy to fix, but others are sometimes more difficult. No matter what the problem is, it is imperative that you become knowledgeable about plumbing so you can fix your plumbing issues quickly.

When choosing a plumber make sure he is insured and licensed. This is very important. If there is a plumbing emergency, you want to make sure the plumber has met the training requirements of the state. If he is insured, this covers any accidental damage done while fixing your plumbing.

Roots from a tree in your back yard can be a real headache when it comes to plumbing. Make sure if you have a big tree or bush or some kind of plant with a big root system, that you ask your plumbing company about root killing agents. You can flush these down your toilet and kill any roots that may be blocking your pipes and save yourself a lot of money by stopping a back up before it happens.

Use your garbage disposal with the cold water running so that you can preserve the blades of the disposal. Using Toilet Installation makes grease more liquid and can cause problems, including clogs. Make sure to clean blades by putting in a little dish detergent and run cold water at the same time.

Make sure everyone in your home knows where the main water shut off valve is and that they know how to work it. That way, if there is a water problem, anyone in your household can turn off the water, thereby reducing the chances that your home will incur major water damage.

Frozen and bursting pipes from harsh winter weather is a problem that no-one wants, so plan now to winterize your exterior faucets and pipes against freezing conditions. A simple way to accomplish this is to find the exterior water shut-off valve located inside your home (often located in the basement). Turn off the water valve to stop water flow, and then open up the outside faucets to drain out any water that has collected. Be sure to turn off the outside water faucets tightly after the water has drained out. Take in any hoses you may have outside so they don't crack from the cold weather.

If you have drains in your house that have not been used for a long period of time, pour one gallon of water through them to keep them functional. Furthermore, this will have the added benefit of reducing any odors from entering your house from lack of use during the year.

Do not ignore https://www.realtor.com/advice/buy/what-to-look-for-fixer-upper/ flushing toilet. This is usually a sign that something is wrong. It can also cause backups and overflows. The most common causes of a slow flushing toilet are sediment build up, tank malfunctions, or partial clogs. You should periodically check for these problems.

Make sure to never leave any flammable liquids near your water heater. Certain liquids like gasoline, solvents, or adhesives are flammable, and if left too close to the water heater, can ignite. If you have to have these liquids in your basement, place it far away from your water heater.

Garbage disposals are a common cause of plumbing problems, which is an easy problem to solve. Don't just put everything down the disposal or treat it like a second trash can. Use the disposal things that would be difficult to dispose of normally. Putting all leftover food down the sink is a good way to produce clogs.

If you have a crack in your toilet tank, you can sometimes fix this with an epoxy resin. However, it is very difficult to keep up with this type of maintenance, and the best bet may be contacting the supplier and ordering a new tank to be installed in your bathroom. Nevertheless, keeping some epoxy resin on hand for emergencies is a good idea.

If your toilet has sewage back-up, then there is a block somewhere along the branch line that connects the sewage and main lines. Get help from a professional. A plumber will run a snake in the line to clear it.

Teach kids how to shut off the toilet's water supply. Kids are notorious for putting large wads of toilet paper and other things into the toilet, which inevitably leads to the toilet overflowing. Especially if your bathroom has carpet, show kids how to turn the water valve off if the toilet water keeps rising, to prevent the mess of an overflow.

Be sure that you check on your water meter when it is not being used. Then, check on the meter 8 hours later. If the meter has changed, even a small amount, this could be a sign that there is an undetected water leak, which can be a severe problem.

A great way to save a few dollars is to add insulation to your hot water heater. Much of the energy required to heat the water in your home is the expense from keeping the water in the tank hot for when it is needed. Adding an extra layer of insulation can help reduce this cost.

To prepare for the cold weather, properly drain all outside faucet bibs and turn off the water supply to those faucets. A piece of foam taped to the outside bib can provide excellent insulation to prevent any remaining water from freezing or splurge for a specialty cover that comes complete with velcro closures.

Investigate loose tiles for sign of water damage. Tiles that are not tight can be a warning sign that you have a leak. Feel each tile carefully to see if there is enough resistance. If the tile does yield, the problem should be investigated immediately. It is much easier to fix a plumbing problem in its early stages.

Protect you plumbing pipes! If you live in an area which has cold winters and are leaving your home for an extended amount of time, protect your plumbing while you are gone! Shut off the main water valve! Drain the system of water by opening the faucets at the highest and lowest points of the house. Also, make sure that you have left some heat on in the house! Set the thermostat to at least 55 degrees Fahrenheit.


When installing a new water heater you need to keep your budget in mind for the upcoming purchase. Low entry gas water heaters usually start around $200 and they usually hold 40 to 50 gallons. web link start around $400 and they usually have extra features like 12 year warranties.

Fair enough, you're not going to become an expert overnight - but there are surely one or two pieces of advice here that you can use. Every job that you do yourself is one less job that you have to pay someone else to do!

Need To Tackle A Plumbing Emergency Situation? Take A Look At These Tips First!

https://goo.gl/46y47C or ongoing plumbing problems can damage your home as well as your belongings. Here are some tips to help you begin fixing whatever plumbing problems you may need help with.

Don't pay a plumber until the job is completed. A plumber may require some money upfront, but it's wise to wait until the job is completely done before giving him the entire payment. Many things can happen between the stop and end of a job, so to be safe wait until you are satisfied with the completed work before paying.

Before you start a plumbing project you should tighten all of the pipes that are easily accessible. Especially if Clogged Plumbing Solutions are making a range of loud banging sounds, as this is a clear sign that there are loose pipes along the line. It is also a good idea in case there is a clog so the excess pressure released does not break a loose pipe.

It is not always necessary to call in a plumber when you have a damaged section of pipe in your plumbing. There are repair kits you can buy in your local hardware store which are excellent in repairing leaks. If you have a small leak, you can rub a compound stick over the hole or crack in the pipe to seal it shut. Epoxy paste is also an excellent remedy for a leaking pipes. Make sure you turn off the water and completely dry the pipe before applying the epoxy.

Frozen and bursting pipes from harsh winter weather is a problem that no-one wants, so plan now to winterize your exterior faucets and pipes against freezing conditions. A simple way to accomplish this is to find the exterior water shut-off valve located inside your home (often located in the basement). Turn off the water valve to stop water flow, and then open up the outside faucets to drain out any water that has collected. Be sure to turn off the outside water faucets tightly after the water has drained out. Take in any hoses you may have outside so they don't crack from the cold weather.

Drain the sediment from the bottom of your hot water heater twice a year to keep the hot water heater working at its optimal levels. Simply open https://www.nbcphiladelphia.com/news/local/Trench-Collapse-Worker-Trapped-491037111.html and allow the water to run out into a bucket until the water runs clear. Then close the drain valve.

If your plumbing is making strange noises you may have lost something called your "air cushion". To turn this back on, you're going to need to turn off your main water supply. Run all faucets in your house and then turn back on your main water supply. This should make everything sound better again.

Treating your drains every month is a great way to avoid future clogs and other problems, and it's a very simple procedure. Just run one to two gallons of hot tap water down each drain in your house.


To avoid freezing pipes in the winter, make sure to insulate any exposed pipes in you basement before winter comes. Pay extra attention to pipes near the outside walls. If you have had a problem with any particular pipe freezing in the past, apply some heat tape to insulate those pipes.

If you own property where the temperature gets below freezing for an extended amount of time each year, you should make sure that pipes located in unheated areas, such as crawl spaces and garages, are insulated. Pipes that are exposed to the outside elements or those that are prone to freezing, should be protected by heat tape or thermostat-controlled heat cables to prevent them from freezing.

Many people deal with clogged toilets. However, if your toilet will not flush every time, the water rises to the top, and there is bubbling effect occasionally, this can be due to a much deeper blockage in the main pipe. https://goo.gl/w9aF5w must then be cleaned in order for your toilet to work properly.

Always keep a trash bin in the bathroom so that you can dispose of cotton swabs, facial pads, and hair. Do not put these materials in the toilet as they can cause clogs over time and disrupt your water flow. These items will not dissolve or break down when submerged in water.

Insulate your pipes properly. If the temperature drops below fifty five degrees, your pipes could freeze. This makes pipes extremely fragile and increases the risk of leaks and damages. The pipes inside your house should not freeze but take a look at a plan of your plumbing system to see if you have any pipes outside of your house.

During the week, hair and soap can build up in your drains and can cause serious clogs. Make sure that you have strainers in each of your drains to help catch this debris so that it does not become an issue. This will help to keep your water flowing efficiently.

While it might help to conserve a bit of water to not flush the toilet after every use or only under certain conditions, regularly flushing toilets can help keep water moving in pipes and prevent freezing. The same holds true for letting water run in sinks as well. If you have rarely used bathrooms in your home, make it point to to flush the toilets and run the faucets on a regular basis.

For people who live in an apartment complex, plumbing is often forgotten about. The first time they move into a home they are unable to resolve any minor plumbing problems, because they have never dealt with this kind of thing. It is good to get a basic understanding when moving into your first house.

Kitchen and bathroom plumbing is often located on exterior walls and freezes more easily than interior wall plumbing. Keep your furnace at a safe temperature throughout the winter and open cabinet doors in bathroom vanities and beneath kitchen sinks to expose the pipes to warmer room air to prevent freezing.

If you need to drill holes in your walls or ceilings, start with a hole big enough to fit your hand through it. Take a picture of the inside with a camera or a cell phone. Make sure you activate the flash function and take several pictures in different directions.

A bad faucet might need new parts. If you need to change the cap, cut it on the side with a rotary tool. Cut the exterior part and the plastic seal, but make sure you stay clear of the brass inside of it. You can easily replace the exterior of the cap and the seal.

So, after reading and applying the helpful tips listed above, you should feel a bit more at ease in the land of plumbing. You have the tools; it's time to use them. You should feel empowered and ready to begin your plumbing journey to start taking care of your home's plumbing system.

Leaky Faucet? Tips On How You Can Repair Minor Issues

Are you intrigued by how your plumbing system works? Plumbing can be intimidating to many people on the surface, but it is really not that difficult to learn. Many plumbing issues can be addressed by a simple fix. You can start learning more about plumbing by reading this article for some useful tips.

Rigid copper is used for main water lines in many homes. You cannot bend rigid copper, so joints and tees must be soldered on. When soldering, always apply flux (also called soldering paste) to both surfaces. find more when the copper is heated. Always use lead-free or nearly lead-free solder when sweating a copper joint.

You need to winter-proof your house. You have to make sure you switch of the master circuit breaker or the shut-off valve before you leave your house. Since one small hole or congested water can quickly freeze and cause pipes to break and expand, you need to drain and open all outdoor and household water lines.

One of the things that you can do to maximize the security of your home is to seal all of the cracks in your outdoor faucets. Even a tiny crack can intensify as the season progresses and lead to serious problems down the road. Reduce drips and leaks for optimal protection.

Check your gas water heater periodically to make sure the pilot flame is lit. The correct color for this flame should be blue. The tip of the flame should be yellow. If https://goo.gl/43AncD find that you are only seeing a yellow flame, you may need to call a professional for safety reasons.

Don't pay the entire plumbing bill upfront; wait until the plumber finishes the plumbing job. It is customary to put down one-third to one-half of the total cost before the work is started, but do not pay in full until it is complete. Knowing the job was completed in a timely and high-quality manner is essential before paying for a plumber.

Check carefully around the base of your toilet for any damage caused by leaks. Straddle the toilet, so you can rock from one leg to another to determine whether there's weakness in the floor. By noticing a problem early on, you can save yourself a bunch of money if you were to leave it alone.

Work with plumbers that offer flat rates. When a plumber is charging by the hour, they do not have an incentive to get the job done quickly. It is human nature to go just a little bit slower if it'll mean extra money in our pockets. If you cannot find someone who charges per project make sure that you are vigilant in watching the clock and their work.


You can remove unsightly mineral buildup from your shower head by soaking it in vinegar overnight. This loosens the deposits, and in the morning you only need to wipe off the residue with a rag. If Plumbing Parts Repair is high up an not removable, place vinegar in a plastic bag, slip the bag over the shower head and hold in place with a twist tie.

If you have a crack in your toilet tank, you can sometimes fix this with an epoxy resin. However, it is very difficult to keep up with this type of maintenance, and the best bet may be contacting the supplier and ordering a new tank to be installed in your bathroom. Nevertheless, keeping some epoxy resin on hand for emergencies is a good idea.

Make sure to pour a gallon or two of water into drains that are used infrequently. Not only does this make sure that they are clear when you need them, but can also fill the trap and make sure that unpleasant odors don't enter your home. Doing https://rocket-plumbing-plumber-santa-monica.business.site/ will also help you to catch problems before they become serious.

Avoid pouring grease or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there's a place to recycle it near your home.

Hair can clog your drains if you do not clean them regularly. You could also get some screens to place over your drains to keep most of the hair from going down. Hair usually breaks down, but it can cause your drains to back up if they are present in large quantity.

When you are working on any kind of plumbing project, you always need a backup person. This is because, when working with water, you never know when an emergency can happen and that second pair of hands can come in very useful! This can even be an unskilled person who can follow directions.

If the water pressure on your street exceeds 60 pounds, you many want to consider installing a pressure reducing valve. Too much water pressure is actually harmful to your plumbing system and could cause excess water pressure. A pressure reducing valve cuts down your water pressure by almost 50 percent.

If you think you understand what is wrong with your toilet, but aren't sure, you should first do some more research on the internet. Most plumbing problems are fairly standard, and you should be able to read about the problem in great detail on several amateur plumber forums to make sure you understand the problem.

If you have a water pressure or fill problem throughout the whole house, do not panic. It could be the simplest of solutions. Sometimes the city flushes their systems, breaking up debris and sending it to homes. This requires cleaning drains effectively and strainers in order to resolve the problem.

Look at your hot water heater and make sure that the temperature is not higher than 120 degrees Fahrenheit. If it is, it could cause you to get burned or it could reduce the unit's energy consumption. If you determine that the temperature is too high, adjust immediately to avoid any of these things from happening.

Before your plumber begins work in your home, make sure you receive a detailed estimate detailing the work to be done, parts needed, a time line and projected completion date. Having all of this information beforehand will give you an idea of what the costs are going to be and how long everything should take.

There are times when a plumber's service is necessary. However, many plumbing issues can be addressed easily if you know how. Learning more about how your plumbing works can save you time and money in repairs. Remember these tips, and they could save you a lot of headaches the next time you have a plumbing problem.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15